Testing that Reaches the World
Mechanical & Fatigue Testing
Torque & Rotary Fatigue Testing Services
Clark Testing performs torsional load, torque fatigue and rotary fatigue testing on shafts, rods, pipes, tubes and other rotating components. Our laboratory offers multiple rotary test systems, including a Tinius Olsen torsional load frame, for static and cyclic loading programs.
Testing Overview
What Is Torque and Rotary Fatigue Testing?
Torque testing evaluates how a component responds to twisting loads. Rotary fatigue testing applies repeated torsional or rotational loading to examine durability, fatigue behavior and potential failure modes over a defined number of cycles.
Clark Testing conducts programs on motor shafts, propeller shafts, rods, pipes, tubes, studs and threaded connectors. Depending on the test plan, specimens may be cycled for a specified duration or tested to failure. Repeated loading can initiate and propagate fatigue cracks, particularly at areas of concentrated stress.
Documented Laboratory Equipment
Torque Testing Capacity
The original laboratory description identifies a range of equipment for static torsional loading and rotary fatigue testing.
Tinius Olsen Torsional Load Frame
- Static torsional load: 600,000 in-lb
- Rotation: Unlimited
- Bed length: Up to 240 in. (20 ft)
Large-Scale Rotary Fatigue
- Rotary 6 listed capacity: 400,000 lb-ft
- Specimen length: Up to 90 ft on the large-scale system
- Angular rotation: ±15° on Rotary 6
- Frequency: Up to 1 Hz on Rotary 6, depending on angular rotation
Capacity confirmation: The original overview also states a 200,000 lb-ft general capability, while its equipment list specifies 400,000 lb-ft for Rotary 6. Confirm the applicable rating and configuration with our team before defining a test program.
Torque Testing Capabilities
Rotary Fatigue Test Systems
The source lists six rotary systems. Operating frequency and allowable motion depend on the selected configuration and test conditions.
Rotary 1
25,000 lb-ft; ±50° angular rotation; variable bed length up to 102 in.; up to 10 Hz depending on rotation.
Rotary 2
12,500 lb-ft; ±90° angular rotation; 96 in. bed, with the source also referencing configurations up to 90 ft; up to 10 Hz depending on rotation.
Rotary 3
2,500 lb-ft; ±180° angular rotation (360° total); 102 in. bed, with the source also referencing configurations up to 90 ft; up to 10 Hz depending on rotation.
Rotary 4
12,500 lb-ft; ±180° angular rotation; source lists 96 in. to 90 in. bed dimensions, which should be confirmed; up to 10 Hz depending on rotation.
Rotary 5
417 lb-ft; ±100° angular rotation; 3 ft bed; up to 10 Hz depending on rotation.
Rotary 6
400,000 lb-ft; ±15° angular rotation; 90 ft bed; up to 1 Hz depending on rotation.
Torque Testing Capabilities
Components and Test Objectives
Test programs can be tailored to component geometry, required loading and acceptance criteria.
Motor and Propeller Shafts
Evaluate torsional response and cyclic durability of rotating shafts.
Rods, Pipes and Tubes
Apply controlled twisting loads to assess torsional performance and fatigue behavior.
Studs and Threaded Connectors
Examine components susceptible to cyclic stress and fatigue-crack initiation.
Static Torsional Loading
Apply a defined torque to assess component response or ultimate strength as specified by the test plan.
Cyclic Fatigue to Duration or Failure
Run specimens for a defined number of cycles or until failure, according to customer requirements.
Failure Examination
Clark Testing identifies scanning electron microscopy (SEM) as an available resource for microscopic analysis following testing.
Test Planning
What to Include in a Torque Testing RFQ
Provide the component drawing, material, overall dimensions, fixture requirements, target torque, angular rotation, cycle count, frequency and required reporting. Indicate whether the test is intended for qualification, comparative evaluation, durability or failure investigation.
Related capabilities include Fatigue Load Testing, Load Testing and Mechanical Structures, Fatigue & Load Testing.
Frequently Asked Questions
Torque Testing FAQs
What is the difference between torque testing and rotary fatigue testing?
Torque testing evaluates response to a twisting load. Rotary fatigue testing repeatedly applies torsional or rotational loads to assess durability and fatigue behavior.
Can Clark Testing evaluate long shafts?
The original laboratory equipment list identifies a large rotary system with a 90 ft bed. Specimen fit and fixture requirements must be reviewed for each project.
What torque capacity is available?
The Tinius Olsen frame is listed at 600,000 in-lb static torsional load. Rotary systems span several listed capacities, including a 400,000 lb-ft Rotary 6 system. Confirm the applicable configuration and rating with the laboratory.
Can specimens be tested to failure?
Yes. The original service description identifies programs run to a specified cyclic duration or to failure, depending on the test plan.
What information is reported after a fatigue failure?
The original page describes reporting stress concentrations, cycles experienced, stresses during cycling and the applicable failure mode, as defined by the test program.
Plan Your Test Program
Need Torque or Rotary Fatigue Testing?
Send Clark Testing your component details and loading requirements. Our team can review equipment fit, fixtures, cycling conditions and reporting needs.